1hp 2hp 3hp 4hp 5hp Head Clean Pool Pump Impeller Swimming Pool
Pump 1.1hp
| Model | Voltage | HZ | Power(KW) | Power(HP) | Hmax(m) | Qmax(m³/h) | Port Size(inch/mm) |
| FL-150 | 220V-240V | 50/60 | 1.1 | 1.5 | 18 | 30 | 2.0/63 |
| FL-200 | 220V-240V | 50/60 | 1.5 | 2 | 19 | 35 | 2.0/63 |
| FL-300 | 220V-240V | 50/60 | 2.2 | 3 | 20 | 38 | 2.0/63 |
| FL-350 | 220V-240V | 50/60 | 2.6 | 3.5 | 21 | 40 | 2.0/63 |
| FL-400 | 380V | 50/60 | 3 | 4 | 22 | 48 | 2.0/63 |
Features:
1. Excellent Flow rate suitable for spas and pools up to 2000
litres
2. Suitable for spas including Salt, Chorine, Inground and Above
Ground
3. Corrosion Resistant and Chemical-resistant thermoplastic body
4. Tough durable construction for longer lasting life
5. Built-In Thermal Protection
6. Instruction manual for ease of installation and use.
7. Anti spin-off impeller.
8. A large see-through strainer, super-size debris basket.
9. Special design shockproof basement
10. Good quality and modern design
11. Low operation noise
12. Single or three phase
13. Anodized motor body
14. Huge pro-filter for less cleaning maintenance
Release all air from fitter and piping system: see filter owner
manual
In a flooded suction system (water source higher than pump),
pump will prime.
it self when suction and discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove cap
cover; fill cap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace cap cover on cap turn clockwise to tighten cover.
PRIMING PUMP
NOTICE:
Tighten cap cover by hand only
Pump should prime now. Priming time will depend on vertical length
of suction lift and horizontal
of suction piping.
ROUTINE MAINTENANCE
The only routine maintenance is inspection/cleaning basket. Debris
or trash that collects in basket,
well choke off water flow through the pump. Follow instructions
below to clean basket:
Stop pump, close gate valve in suction and discharge, and release
all pressure from
system before proceeding.
1. Unscrew cap lid(turn counterclockwise).
2. Remove strainer basket and clean. Be sure all holes in basket
are clear, flush basket with water.
If basket is replaced backwards, cover will not fit on pre-filter
body.
3. Clean and inspect lid Ring: re-install on cap cover.
4. Clean Ring groove on pre-filter body and Replace lid. To help
keep lid from sticking, tighten
hand tight only.
5. Prime pump (see priming instructions above)
Description:
HOW TO USE – It is best to always replace your pump with a pump of
similar size and power rating. Changing over and fitting of the
pump can be done by the handy person but it is recommended to get
it done by a professional. Suitable as a direct replacement OR
upgrade to existing pump.
This pump is ideal for pool pumping, cleaning, hot water
circulation etc. Sometimes people use it for increasing the water
pressure in the pipe, garden sprinkling, and irrigation. It only
needs solar off grid power to get work! Delivery head of 14 meters
and suction up to 8 meters. This pump is simple to install and easy
to use. No need of sophisticated knowledge of pumping but just a
little imagination of how much you can do with it. It will pump up
the water in no time.
